Gilbert, Arizona #31
1323 N. Tech Blvd.,
Gilbert, AZ 85233
Phone: (480) 969-9988
Fax: (480) 969-2850
Email: mes@rsd.net
Store Hours
Mon-Fri: 7:00 a.m. - 5:00 p.m.
Store hours may vary
due to holidays and events.
Branch ManagerDan Weaver
Dan Weaver has been an employee with RSD since
April 1985.
Driving Directions
Upcoming Branch Events for Gilbert
Contact: Dan Weaver @: (480) 969-9988
December 21, 2023
08:00:00
Inverter Installation & Diagnostics
RSD is hosting a Bosch Inverter Installation and Diagnostics training. Bosch instructors will be covering proper installation techniques to avoid any start-up issues and unit failures. Technicians will learn how to navigate through the user interface to set up and diagnose troubleshooting along with any maintenances. Technicians will receive service manuals and a quick start guide to assist them in the field.
January 11, 2024
08:00:00
Harris Alloys Training Workshop
This will be a hands-on training on aluminum-to-aluminum brazing, copper-to-copper brazing, and the proper safety, setup, and use of oxygen and fuel equipment. Technicians will learn the six fundamental steps for brazing and how to masterly braze and solder techniques for your application. Attendees will receive recommendations for equipment and consumables specific to each operation as well as a NATE Continuing Education Hour Credits for applicable courses
January 18, 2024
08:00:00
Sub-cooling & Superheat Saturation
This Testo program is for the HVAC professionals who want to learn more about the Pressure/Temperature Relationships in AC, Refrigeration systems, and how to correctly measure the performance of the system by looking at Superheat and Sub-Cooling. The course offers a better understanding of the refrigeration cycle, its components, and analog gauges vs. digital manifolds. It will provide a collection of knowledge in the Laws of Refrigeration and Heat Transfer.
February 01, 2024
08:00:00
The Importance of CO/Combustion Testing
RSD is hosting an Importance of CO/Combustion-Testing seminar with Testo. The course provides a collection of detailed knowledge in testing recommendations, instrumentation maintenance, calibration, service and insights into applying these safely and efficiently. It will offer a better understanding of the basic theories of combustion, CO safety standards, and environmental compliance in commercial and residential fuel burning appliances.
February 08, 2024
08:00:00
New Low GWP Refrigerants: Regulations and the Future
With R22 in the rearview mirror, regulations are now focusing on Climate Change. This has put HFC and HFO refrigerants on the clock and has seen the introduction of new rules and regulations that will have a significant impact on new equipment, and existing system retrofits. This presentation will address where we are, what new rules are on the horizon, and how these will change our industry forever.
February 15, 2024
08:00:00
RUUD Mid and High Seer Inverter
RSD is hosting a Ruud High / Mid Seer Inverter training. The course will provide a better understanding of proper installation, service, and maintenance of Ruud's High / Mid Seer inverter equipment. It will also cover the Econet Thermostat installation, setup, and use as a diagnostic tool for infield service. In addition to the new Ruud Bluetooth app and how it can be used in equipment setup.
February 23, 2024
08:00:00
Aftermarket PSC/ECM Training
RSD is hosting an aftermarket PSC/ECM motor class. The course will provide a basic understanding of ECM motors and how they operate. It will offer a better understanding of the difference between PSC versus ECM motors. Topics on how to replace a PSC motor with an ECM motor, as well as an OEM motor with an aftermarket ECM for half the price will also be covered.
February 27, 2024
07:30:00
Fieldpiece Job Link Training
RSD is hosting a Job Link seminar with Fieldpiece. The course will discuss the tools along with the app in detail for technicians to get the most out of both to collect the necessary data for unit diagnosis and maintenance. Then to have the ability in creating a PDF straight from the app to be shared with management, other technicians, and or their customers.
March 14, 2024
08:00:00
RUUD Air Flow Basics
RSD is hosting an Air-Flow trouble shooting class. We will discuss the basics of unit air flow diagnosis and perform hands on air flow measurements using some of the basic tools used to measure air flow. Technicians will walk away with a better understanding on how to measure static pressure and the ability to use the tools to take the measurements correctly.
March 21, 2024
08:00:00
IntelliGen Refrigeration Controller
RSD is hosting an IntelliGen refrigeration controller workshop with Heatcraft. This hands-on training provides an in-depth insight over IntelliGen's features, benefits, and technical information. It will offer a better understanding of installation guidelines/setup, programming menus, operation sequence, diagnosis, and remote access.